cheap chip & minolta trouble http://copierservicereset.com HOW TO RESET COPIER'S CHIPS IN THE CHEAPEST MODE Mon, 08 Mar 2010 17:20:33 +0000 http://wordpress.org/?v=2.7.1 en hourly 1 trouble code list minolta cf1501/2001 http://copierservicereset.com/trouble-code-list-minolta-cf15012001 http://copierservicereset.com/trouble-code-list-minolta-cf15012001#comments Mon, 08 Mar 2010 17:07:09 +0000 admin http://copierservicereset.com/?p=372

C0000 Main Motor

’s failure to turn The Main Motor Lock signal remains faulty for a predetermined’s’s’s failure’s’s failure to turn’s failure to turn’s failure to turn’s failure to turn

C0060 Fusing Drive Motor

to turn

A Fusing Drive Motor Lock signal remains faulty for a

predetermined continuous period of time while the

Fusing Drive Motor is turning.

C0061 Fusing Drive Motor turning

at abnormal timing

The Fusing Drive Motor Lock signal remains faulty

for a predetermined continuous period of time while

the Fusing Drive Motor remains stationary.

C0094 2nd Image Transfer Roller

pressure/retraction failure

’s failure

•

is not activated (retracted position) within 1 sec.

after the 2nd Image Transfer Roller has started its

retracting motion.

The 2nd Image Transfer Pressure Position Sensor

•

is not deactivated (not the retracted position)

within 1 sec. after the 2nd Image Transfer Roller

has started its pressing motion.

C0096 1st Image Transfer Roller

pressure/retraction failure

The 2nd Image Transfer Pressure Position Sensor

•

is not activated (retracted position) within 3

sec. after the 1st Image Transfer Pressure/Retraction

Motor has started turning.

The 1st Image Transfer Retraction Position Sensor

•

is not deactivated (pressed position) within 1.5

sec. after the 1st Image Transfer Pressure/Retraction

Motor has started turning.

C0098 Fusing Roller pressure/

retraction failure

The 1st Image Transfer Retraction Position Sensor

•

after the lapse of 0.5 sec. after the Fusing Pressure/

Retraction Motor has started turning for

retraction direction during retraction control.

No change is observed in the encoder pulse even

•

after the lapse of 0.5 sec. after the Fusing Pressure/

Retraction Motor has started turning for pressure

direction during pressure control.

No change is observed in the encoder pulse even

•

(pressed position) even when 31 motor

encoder pulses have been counted after the Fusing

Pressure/Retraction Motor has started turning

for pressure direction during pressure control.

C0200 Cyan PC Drum Charge

Corona malfunction

The SCD signal remains inactive for a continuous 1-

sec. period while charge corona is being output (i.e.,

the Remote signal is being turned ON).

C0202 Magenta PC Drum Charge

Corona malfunction

The SCD signal remains inactive for a continuous 1-

sec. period while charge corona is being output (i.e.,

the Remote signal is being turned ON).

C0204 Yellow PC Drum Charge

Corona malfunction

The SCD signal remains inactive for a continuous 1-

sec. period while charge corona is being output (i.e.,

the Remote signal is being turned ON).

C0206 Black PC Drum Charge

Corona malfunction

The SCD signal remains inactive for a continuous 1-

sec. period while charge corona is being output (i.e.,

the Remote signal is being turned ON).

Code Description Detection Timing

The Fusing Pressure Position Sensor is not activated

C0400 Exposure Lamp

turn ON

A Lamp-Out Detection signal is ON after the lapse of

5 sec. after the Exposure Lamp has been turned ON.

C0410 Exposure Lamp turning

ON at abnormal timing

CCD Sensor outputs are written in line RAM at the

end of a scan job and the average of these readings

exceeds a predetermined value.

C0500 Heating Roller warm-up

failure

(Fusing Thermistor 1)

’s failure to

•

temperature and the warm-up cycle is not

completed within the period of 9 min. 10 sec. after

the warm-up cycle has been started.

Fusing Thermistor 1 does not detect a predetermined

•

rise to a level more than the predetermined output

value within 30 sec. after the warm-up cycle has

started.

C0501 Lower Fusing Roller

Heater Lamp warm-up failure

(Fusing Thermistor 2)

The temperature of Fusing Thermistor 1 does not

•

reach 100

cycle has started.

The temperature of Fusing Thermistor 2 does not°C within 180 sec. after the warm-up

•

rise to a level more than the predetermined output

value within 130 sec. after the warm-up cycle has

started.

C0510 Heating Roller abnormally

low temperature

(Fusing Thermistor 1)

The temperature of Fusing Thermistor 1 does not

•

below 120

state.

The temperature of Fusing Thermistor 1 remains°C for 1 sec. or more in the standby

•

below 130

cycle.

The temperature of Fusing Thermistor 1 remains°C for 1 sec. or more during a print

•

below 90

Saver mode.

C0511 Lower Fusing Roller

Heater Lamp abnormally

low temperature

(Fusing Thermistor 2)

The temperature of Fusing Thermistor 1 remains°C for 1 sec. or more in the Energy

•

below 100

state.

The temperature of Fusing Thermistor 2 remains°C for 1 sec. or more in the standby

•

below 100

cycle.

The temperature of Fusing Thermistor 2 remains°C for 1 sec. or more during a print

•

below 100

Saver mode.

C0520 Heating Roller abnormally

high temperature

(Fusing Thermistor 1)

The temperature of Fusing Thermistor 1 remains

above 220

C0521 Lower Fusing Roller

Heater Lamp abnormally

high temperature

(Fusing Thermistor 2)

The temperature of Fusing Thermistor 2 remains

above 190

Code Description Detection Timing

The temperature of Fusing Thermistor 2 remains°C for 1 sec. or more in the Energy°C for 1 sec. or more at all times.°C for 1 sec. or more at all times.

C0650 Scanner Home Sensor

malfunction

•

Scanner at its home position though the Scanner

is so located.

The Scanner Home Sensor fails to detect the

•

Scanner though the motor has been energized to

move the Scanner over the maximum distance.

The Scanner Home Sensor fails to detect the

•

its home position though the Scanner has moved

5 mm away from the home position.

C0660 Scanner overrun failure The Scanner Home Sensor detects the Scanner at

its home position during a period from when the

prescan command and scan preparation command

have been executed to when home return command

is executed.

C0990 LCC Lift-Up Motor malfunction

See the relevant Option Service Manual.

C0991 LCC Lift 1 ascent motion

failure

C0995 LCC Transport Motor malfunction

C0999 LCC Lift 2 ascent motion

failure

C0B00 Finishing option transport

drive malfunction

C0B20 Stapling Unit CD drive

malfunction

C0B30 Finishing option Paper

Aligning Bar moving mechanism

malfunction

C0B48 Finishing option Exit Roll

pressure/retraction failure

C0B4A Finishing option Storage

Roller pressure/retraction

failure

Code Description Detection Timing

The Scanner Home Sensor detects the Scanner at

C0B50 Finishing option stapling

mechanism 1

See the relevant Option Service Manual.

C0B54 Finishing option stapling

mechanism 2

C0B73 Finishing option punch

cam motor mechanism

malfunction

C0B78 Finishing option punch

selector motor mechanism

malfunction

C0B80 Finishing option Shift

Motor mechanism malfunction

C0BA0 Finishing option Elevator

Tray drive failure

C0F30 Abnormally low toner density

detected by Cyan

ATDC Sensor

Toner density that is 2 % or more lower than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F31 Abnormally high toner

density detected by Cyan

ATDC Sensor

Toner density that is 4 % or more higher than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F32 Abnormally low toner density

detected by Magenta

ATDC Sensor

Toner density that is 2 % or more lower than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F33 Abnormally high toner

density detected by

Magenta ATDC Sensor

Toner density that is 4 % or more higher than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F34 Abnormally low toner density

detected by Yellow

ATDC Sensor

Toner density that is 2 % or more lower than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F35 Abnormally high toner

density detected by Yellow

ATDC Sensor

Toner density that is 4 % or more higher than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F36 Abnormally low toner density

detected by Black

ATDC Sensor

Toner density that is 2 % or more lower than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F37 Abnormally high toner

density detected by Black

ATDC Sensor

Toner density that is 4 % or more higher than the target

level is detected ten consecutive times during a

print cycle, ATVC, or image stabilization sequence.

C0F3A Cyan ATDC Sensor

adjustment failure

Cyan ATDC Sensor adjustment does not function

properly, failing to adjust to an appropriate value.

C0F3B Magenta ATDC Sensor

adjustment failure

Magenta ATDC Sensor adjustment does not function

properly, failing to adjust to an appropriate value.

C0F3C Yellow ATDC Sensor

adjustment failure

Yellow ATDC Sensor adjustment does not function

properly, failing to adjust to an appropriate value.

Code Description Detection Timing

C0F3D Black ATDC Sensor

adjustment failure

Black ATDC Sensor adjustment does not function

properly, failing to adjust to an appropriate value.

C13C8 New Transfer Belt Unit

resetting failure

The output from the new unit detecting terminal

remains HIGH and the copier does not recognize

that a new unit has been installed.

1. After an image stabilization sequence is completed,

the fuse blowout signal of the new unit is

set to a blowout state.

2. After the lapse of 2 sec. after step 1, the fuse

blowout signal is brought to a state where no

new units are installed.

3. After the lapse of 0.1 sec. after step 2, a new unit

check sequence is carried out.

A total of three cycles of steps 1 to 3 are carried out

and, if the copier fails to detect a new unit a third

time, a malfunction condition results.

C13CA New Fusing Unit resetting

failure

The output from the new unit detecting terminal

remains HIGH and the copier does not recognize

that a new unit has been installed.

1. The fuse blowout signal of the new unit is set to a

blowout state.

2. After the lapse of 0.5 sec. after step 1, the fuse

blowout signal is brought to a state where no

new units are installed.

3. After the lapse of 0.1 sec. after step 2, a new unit

check sequence is carried out.

A total of two cycles of steps 1 to 3 are carried out

and, if the copier fails to detect a new unit a second

time, a malfunction condition results.

C13CB New Fusing Web Unit

resetting failure

The output from the new unit detecting terminal

remains HIGH and the copier does not recognize

that a new unit has been installed.

1. The fuse blowout signal of the new unit is set to a

blowout state.

2. After the lapse of 0.5 sec. after step 1, the fuse

blowout signal is brought to a state where no

new units are installed.

3. After the lapse of 0.1 sec. after step 2, a new unit

check sequence is carried out.

A total of two cycles of steps 1 to 3 are carried out

and, if the copier fails to detect a new unit a second

time, a malfunction condition results.

Code Description Detection Timing

C13CC New Oil Coating Unit

resetting failure

The output from the new unit detecting terminal

remains HIGH and the copier does not recognize

that a new unit has been installed.

1. The fuse blowout signal of the new unit is set to a

blowout state.

2. After the lapse of 0.5 sec. after step 1, the fuse

blowout signal is brought to a state where no

new units are installed.

3. After the lapse of 0.1 sec. after step 2, a new unit

check sequence is carried out.

A total of two cycles of steps 1 to 3 are carried out

and, if the copier fails to detect a new unit a second

time, a malfunction condition results.

C13D1 Cyan IU EEPROM failure EEPROM access error:

When EEPROM access control is executed, setting

1

even after the lapse of a predetermined period of

time.

C13D2 Magenta IU EEPROM failure

EEPROM access error:

When EEPROM access control is executed, setting

1

even after the lapse of a predetermined period of

time.

C13D3 Yellow IU EEPROM failure EEPROM access error:

When EEPROM access control is executed, setting

1

even after the lapse of a predetermined period of

time.

C13D4 Black IU EEPROM failure EEPROM access error:

When EEPROM access control is executed, setting

1

even after the lapse of a predetermined period of

time.

C3310 CCD clamp/gain adjustment

failure

“Start Flag” of GA register does not become ready“Start Flag” of GA register does not become ready“Start Flag” of GA register does not become ready“Start Flag” of GA register does not become ready

•

(AVE1 - AVE2) =< 4

When clamp adjustment is made:

•

The average of CCD Sensor output values is 1 or

less.

Dgain = 0

Dgain = 255

C3700 IR Cooling Fan Motor 1

turning at abnormal timing

A Lock signal is detected ten consecutive times

when it is monitored at 0.01-sec. intervals while a

Fan Motor ON signal is being output and, at the

same time, after the lapse of 2 sec. or more after the

output of the Fan Motor ON signal has been started.

Code Description Detection Timing

When gain adjustment is made:

C3710 IR Cooling Fan Motor 2

turning at abnormal timing

A Lock signal is detected ten consecutive times

when it is monitored at 0.01-sec. intervals while a

Fan Motor ON signal is being output and, at the

same time, after the lapse of 2 sec. or more after the

output of the Fan Motor ON signal has been started.

C3720 Original Glass Cooling Fan

Motor turning at abnormal

timing

A Lock signal is detected ten consecutive times

when it is monitored at 0.01-sec. intervals while a

Fan Motor ON signal is being output and, at the

same time, after the lapse of 2 sec. or more after the

output of the Fan Motor ON signal has been started.

C3A00 PIC communication error

predetermined period of time after IREQ has been

received during AIDC sampling of image stabilization

sequence or registration adjustment.

• A sampling lock is not received after the lapse of a

•

between the PIC Board and Master Board.

There is an open-circuit in the communication harness

•

C3A01 PIC Board malfunction The PIC Board is faulty.

C3FFF ROM contents fault

detected upon start

The system fails to rewrite flash memory during

updating.

Either the PIC Board or Master Board is faulty.

continuous period of time while the Main

Motor is turning.

C0001 Main Motor turning at

abnormal timing

The Main Motor Lock signal remains faulty for a predetermined

continuous period of time while the Main

Motor remains stationary.

C0010 Imaging Unit Motor C

failure to turn

The Lock signal remains faulty for a continuous 1-

sec. period after the motor rotation has stabilized

and before the motor starts decelerating.

C0011 Imaging Unit Motor C turning

at abnormal timing

The Lock signal remains faulty for a continuous 1-

sec. period after the motor has completely stopped

and before the motor starts accelerating.

C0012 Imaging Unit Motor M

failure to turn

The Lock signal remains faulty for a continuous 1-

sec. period after the motor rotation has stabilized

and before the motor starts decelerating.

C0013 Imaging Unit Motor M turning

at abnormal timing

The Lock signal remains faulty for a continuous 1-

sec. period after the motor has completely stopped

and before the motor starts accelerating.

C0014 Imaging Unit Motor Y

to turn

The Lock signal remains faulty for a continuous 1-

sec. period after the motor rotation has stabilized

and before the motor starts decelerating.

C0015 Imaging Unit Motor Y turning

at abnormal timing

The Lock signal remains faulty for a continuous 1-

sec. period after the motor has completely stopped

and before the motor starts accelerating.

C0016 Imaging Unit Motor Bk

failure to turn

The Lock signal remains faulty for a continuous 1-

sec. period after the motor rotation has stabilized

and before the motor starts decelerating.

C0017 Imaging Unit Motor Bk

turning at abnormal timing

The Lock signal remains faulty for a continuous 1-

sec. period after the motor has completely stopped

and before the motor starts accelerating.

C0040 Fusing Cooling Fan Motor

2

A Fusing Cooling Fan Lock signal is detected for a

continuous 3-sec. period while Fusing Cooling Fan

Motor 2 is turning.

C0046 Fusing Cooling Fan Motor

1

A Fusing Cooling Fan Lock signal is detected for a

continuous 3-sec. period while the Fusing Cooling

Fan Motor is turning.

C004C Ozone Ventilation Fan

Motor

An Ozone Fan Lock signal is detected for a continuous

3-sec. period while the Ozone Ventilation Fan

Motor is turning.

C004E Power Supply Cooling Fan

Motor

A Power Supply Cooling Fan Lock signal is detected

for a continuous 3-sec. period while the Power Supply

Cooling Fan Motor is turning.

]]> http://copierservicereset.com/trouble-code-list-minolta-cf15012001/feed trouble code list minolta di2510 http://copierservicereset.com/trouble-code-list-minolta-di2510 http://copierservicereset.com/trouble-code-list-minolta-di2510#comments Mon, 01 Mar 2010 21:12:07 +0000 admin http://copierservicereset.com/?p=369

C0000 Main Motor Failure

• The Transport Motor Lock signal remains set to H

for a set period of time while the Transport Motor is

turning.

C0010

Imaging Unit Motor

Failure

• The Imaging Unit Motor Lock signal remains set to

H for a set period of time while the Imaging Unit

Motor is turning.

• The Imaging Unit Motor Lock signal remains set to

L for a set period of time while the Imaging Unit

Motor remains stopped.

C0044 EDH Fan Motor Failure

• Refer to the Service Manual for the relevant

option.

C0045 Cooling Fan Failure

• The Cooling Fan Motor Lock signal remains set to

H for a set period of time while the Cooling Fan

Motor is turning.

• The Cooling Fan Motor Lock signal remains set to

L for a set period of time while the Cooling Fan

Motor remains stopped.

C004E

Power Unit Cooling

Fan Failure

• The Power Unit Cooling Fan Motor Lock signal

remains set to H for a set period of time while the

Power Unit Cooling Fan Motor is turning.

• The Power Unit Cooling Fan Motor Lock signal

remains set to L for a set period of time while the

Power Unit Cooling Fan Motor remains stopped.

C004F IU Cooling Fan Failure

• The I/U Cooling Fan Motor Lock signal remains set

to H for a set period of time while the I/U Cooling

Fan Motor is turning.

• The I/U Cooling Fan Motor Lock signal remains set

to L for a set period of time while the I/U Cooling

Fan Motor remains stopped.

C0214

Abnormal Image

Transfer Voltage

• The image transfer voltage exceeds 100 V for the

set period of time while the Imaging Unit Motor

remains stopped.

C0500

Fusing Warm-Up

Failure (Main)

C0501

Fusing Warm-Up Failure

(Sub)

• The Fusing Roller Sub Thermistor does not detect

the required temperature within 30 sec. after a

warm-up cycle has begun; therefore, the copier

does not complete the warm-up cycle.

• The temperature of the Fusing Rollers does not

reach the required level even after the set period of

time has elapsed during a warm-up cycle.

C0510

Low Fuser Temperature

Failure (Main)

• The Fusing Roller Thermistor and Fusing Roller

Sub Thermistor are detected to be at a temperature

below 105 °C during standby.

• The Fusing Roller Thermistor and Fusing Roller

Sub Thermistor are detected to be at a temperature

below 105 °C during printing.

C0511

Low Fuser Temperature

Failure (Sub)

C0520

High Fuser Temperature

Failure (Main)

• The Fusing Roller Thermistor and Fusing Roller

Sub Thermistor are detected to be at a temperature

above 240 °C when the Power Switch is set to

ON.

• The Fusing Roller Thermistor and Fusing Roller

Sub Thermistor are detected to be at a temperature

above 240 °C when the Power Switch is set to

ON.

C0521

High Fuser Temperature

Failure (Sub)

C0650

Faulty Scanner Home

Position Sensor

• The Scanner Home Position Sensor is not blocked

even after the lapse of a given period of time after

it has been unblocked when the Start key is

pressed.

C0900

3rd Drawer Lift-Up

Motor Failure

• The Lift-Up Sensor is not unblocked even after the

set period of time has elapsed after the paper liftup

operation for the drawer has begun.

C0910

2nd Drawer Lift-Up

Motor Failure

C0920

1st Drawer Lift-Up

Motor Failure

C0950

4th Drawer Lift-Up

Motor Failure

C0960

Manual Bypass Paper-

Lifting Failure

• The Manual Feed Tray Lift-Up Sensor (PC29) is

not blocked or unblocked even after the set period

of time has elapsed after the Manual Paper Feed

Pick-Up Solenoid (SL3) is energized after the manual

feed paper take-up operation has begun.

C0990

LCC Elevator Motor

Failure

]]> http://copierservicereset.com/trouble-code-list-minolta-di2510/feed trouble code list minolta c350 http://copierservicereset.com/trouble-code-list-minolta-c350 http://copierservicereset.com/trouble-code-list-minolta-c350#comments Fri, 26 Feb 2010 19:58:43 +0000 admin http://copierservicereset.com/?p=366

 

C0000Main Motor’s failure to turn • The Motor Lock signal remains HIGH for a predeterminedcontinuous period of time while the Motor is turning.

C0001 Main Motor turning at abnormaltiming

• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

C0016 Bk PC Motor’s failure to turn • The Motor Lock signal remains HIGH for a predeterminedcontinuous period of timewhile the Motor is turning.

C0017 Bk PC Motor’s turning at abnormal timing

• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

C0018 Color PC Drum Motor’s failure to turn

• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

C0019 Color PC Drum Motor’s turning at abnormal timing

• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

C001A Color Developing Motor’s failure to turn

• The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning.

C001B Color Developing Motor’s turning at abnormal timing

• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

C0040 Suction Fan Motor’s failure to turn • continuous period of time while the

The Fan Lock signal remains HIGH for a predetermined

Motor remains stationary.

C0046 Fusing Cooling Fan Motor/1 failureto turn

C0048 Fusing Cooling Fan Motor/1 or FusingCooling Fan Motor/2 failure to turn

C004C Ozone Ventilation Fan Motor’s failure to turn

C004D Toner Suction Fan Motor’s failure toturn

C004E Power Supply Cooling Fan Motor’s failure to turn

C004F Cooling Fan Motor 2’s failure to turn

C0060 Fusing Drive Motor’s failure to turn

C0061 Fusing Drive Motor turning at abnormal timing

• The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary.

C0094 2nd Image Transfer Roller pressure/ retraction failure

• The 2nd Image Transfer Pressure Position Sensor is

not activated (retracted position) within 2 sec. after the

2nd Image Transfer Pressure/Retraction Motor has

started turning during a sequence of the 2nd Image

Transfer Roller’s retracting motion.

• The 2nd Image Transfer Pressure Position Sensor is

not deactivated (pressed position) within 2 sec. after

the 2nd Image Transfer Pressure/Retraction Motor has

started turning during a sequence of the 2nd Image

Transfer Roller’s pressing motion.

C0096 Image Transfer Belt pressure/retraction failure

• The 1st Image Transfer Retraction Position Sensor is

not activated (retracted position) within 5 sec. after the

1st Image Transfer Pressure/Retraction Motor has

started turning during a sequence of the Transfer

Belt’s retracting motion.

• The 1st Image Transfer Retraction Position Sensor is

not deactivated (pressed position) within 1 sec. after

the 1st Image Transfer Pressure/Retraction Motor has

started turning during a sequence of the Transfer

Belt’s pressing motion.

C0098 Fusing Pressure Roller pressure/

retraction failure

• No change is observed in the encoder sensor pulse

even after the lapse of 0.5 sec. after the Fusing Pressure/

Retraction Motor has started turning for a

sequence of the Fusing Pressure Roller’s retracting

motion.

• No change is observed in the encoder sensor pulse

even after the lapse of 0.5 sec. after the Fusing Pressure/

Retraction Motor has started turning for a

sequence of the Fusing Pressure Roller’s pressing

motion.

• The Fusing Pressure Position Sensor is not activated

(pressed position) even when 30 encoder sensor

pulses are counted after the Fusing Pressure/Retraction

Motor has started turning for a sequence of the

Fusing Pressure Roller’s pressing motion.

C0200 Cyan PC Drum Charge Corona

malfunction

• An output is automatically produced from the PC

Drum Charge Corona of each color when the malfunction

resetting procedure is performed after C0208 (PC

Drum Charge Corona malfunction) has been detected.

The SCD signal is detected for a continuous 0.5-sec.

period at this time.

C0202 Magenta PC Drum Charge Corona

malfunction

C0204 Yellow PC Drum Charge Corona

malfunction

C0206 Black PC Drum Charge Corona

malfunction

C0208 PC Drum Charge Corona malfunction

• The SCD signal is detected for a continuous 0.5-sec.

period while the PC Drum Charge Corona is being

energized.

C0400 Exposure Lamp’s failure to turn ON • The output from the CCD Sensor is a predetermined

value or less during CCD Sensor gain adjustment.

C0410 Exposure Lamp turning ON at

abnormal timing

• The average output value of the CCD Sensor with the

Scanner at its standby position is a predetermined

value or more at the end of a scan job.

C0500 Heating Roller warm-up failure • The temperature of the Heating Roller does not reach

100 °C within 50 sec. after the Heating Roller Heater

Lamp has been turned ON.

• The temperature of the Heating Roller does not reach

100 °C and that of the Fusing Pressure Roller does

not reach 195 °C within 200 sec. after the Heating

Roller Heater Lamp has been turned ON.

• The voltage of the Heating Roller Thermistor does not

increase by five steps within 20 sec. after the Heating

Roller Heater Lamp has been turned ON.

• No zero cross signal is detected even with the lapse of

1 sec. or more after the Heating Roller Heater Lamp

has been turned ON.

C0501 Fusing Pressure Roller warm-up

failure

• The voltage of the Fusing Pressure Roller Thermistor

does not increase by five steps within 20 sec. after the

predrive of the Fusing Roller has been started during

a warm-up cycle.

C0510 Heating Roller abnormally low temperature

• No zero cross signal is detected even with the lapse of

1 sec. or more during a standby state, print cycle, or

Power Save.

• A temperature of 120 °C or less of the Heating Roller

is detected for 1 sec. or more during a standby state.

• A temperature of 120 °C or less of the Heating Roller

is detected for 1 sec. or more during a print cycle.

• A temperature of 70 °C or less of the Heating Roller is

detected for 1 sec. or more during Power Save.

C0511 Fusing Pressure Roller abnormally

low temperature

• . A temperature of 80 °C or less of the Fusing Pressure

Roller is detected for 1 sec. or more during a

standby state.

• A temperature of 80 °C or less of the Fusing Pressure

Roller is detected for 1 sec. or more during a print

cycle.

• A temperature of 80 °C or less of the Fusing Pressure

Roller is detected for 1 sec. or more during Power

Save.

C0520 Heating Roller abnormally high

temperature

• A temperature of 225 °C or more of the Heating Roller

is detected for 1 sec. or more.

C0521 Fusing Pressure Roller abnormally

high temperature

• A temperature of 190 °C or more of the Fusing Pressure

Roller is detected for 1 sec. or more before the

start of the heater temperature control.

• A temperature of 215 °C or more of the Fusing Pressure

Roller is detected for 1 sec. or more after the start

of the heater temperature control.

C0650 Scanner Home Sensor malfunction • The Scanner Home Sensor is unable to detect the

Scanner located at its home position.

• The Scanner Home Sensor is unable to detect a Scanner

even when the Scanner Motor has been driven to

move the Scanner over the maximum traveling distance.

• The Scanner Home Sensor detects the Scanner when

the Scanner has moved 5 mm from the position, at

which it blocks the Scanner Home Sensor.

C0660 Scanner overrun failure • The Scanner Home Sensor detects the Scanner at its

home position during a period of time that begins with

the time when a prescan command and a scan preparation

command are executed and ends when a home

return command is executed.

C0900 Tray3 Elevator failure

? See PC-101/PC-201 Service Manual.

C0910 Tray2 Elevator failure • The Lift-up Sensor is not blocked even after the lapse

of a given period of time after the lifting motion has

been started.

C0950 Tray4 Elevator failure

? See PC-201 Service Manual.

C0960 Bypass lifting motion failure • The Bypass Lift-up Sensor is not blocked even when

the Tray2 Vertical Transport Motor has turned for a

given number of pulses after the sequence to move

the Paper Lifting Plate from the standby position to the

take-up position was started.

• The Bypass Lift-up Sensor is not unblocked even

when the Tray2 Vertical Transport Motor has turned for

a given number of pulses after the sequence to move

the Paper Lifting Plate from the take-up position to the

standby position was started.

C0990 LCT Elevator Motor malfunction

(Elevator malfunction)

?

See PC-401 Service Manual.

C0991 LCT ascent motion failure

(soft limit error)

C0996 LCT Shift Motor malfunction

C0997 LCT shifting failure

C0998 LCT ejection failure

C099C LCT Shift Gate malfunction

C099D LCT communications error

C0F30 Abnormally low toner density

detected Cyan ATDC Sensor

• T/C 0.21 % or less is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F31 Abnormally high toner density

detected Cyan ATDC Sensor

• T/C 15.5 % or more is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F32 Abnormally low toner density

detected Magenta ATDC Sensor

• T/C 0.21 % or less is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F33 Abnormally high toner density

detected Magenta ATDC Sensor

• T/C 15.5 % or more is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F34 Abnormally low toner density

detected Yellow ATDC Sensor

• T/C 0.21 % or less is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F35 Abnormally high toner density

detected Yellow ATDC Sensor

• T/C 15.5 % or more is detected ten consecutive times

in the Developing Unit as validated through the toner

replenishing amount determination control.

C0F36 Abnormally low toner density

detected Black ATDC Sensor

• T/C 3 % or less is detected ten consecutive times in

the Developing Unit as validated through the toner

replenishing amount determination control.

C0F37 Abnormally high toner density

detected Black ATDC Sensor

• T/C 12 % or more is detected ten consecutive times in

the Developing Unit as validated through the toner

replenishing amount determination control.

C0F3A Cyan ATDC Sensor adjustment failure

• ATDC Sensor automatic adjustment does not function

properly, failing to adjust to an appropriate value.

C0F3B Magenta ATDC Sensor adjustment

failure

C0F3C Yellow ATDC Sensor adjustment

failure

C0F3D Black ATDC Sensor adjustment

failure

C1200 Standard controller configuration

failure

• The controller of the MFP Control Board (PWB-MFP)

is faulty.

C1203 File Memory mounting error • The File Memory mounted on the MFP Control Board

(PWB-MFP) is faulty.

C1204 Memory capacity discrepancy • The capacity of the File Memory mounted on the MFP

Control Board (PWB-MFP) is short.

C1220 Image Input Time Out • Image data is not input from the Image Processing

Board (PWB-C) to the MFP Control Board (PWBMFP).

C1229 Image Output Time Out • No image data is output from the MFP Control Board

(PWB-MFP).

C1240 JBIG0 Error • Memory of the MFP Control Board (PWB-MFP) is

C1241 JBIG1 Error faulty.

C1242 JBIG2 Error

C1243 JBIG3 Error

C1250 Compressor 0 command buffer

stop failure

• The MFP Control Board (PWB-MFP) is faulty.

C1251 Compressor 1 command buffer

stop failure

C1252 Compressor 2 command buffer

stop failure

C1253 Compressor 3 command buffer

stop failure

C1261 Compression hardware timeout • The hardware involved with the compression function

offered by the MFP Control Board (PWB-MFP) does

not respond.

C1265 Extraction hardware timeout • The hardware involved with the extraction function

offered by the MFP Control Board (PWB-MFP) does

not respond.

C1279 PCI-SDRAM DMA operation failure • The hardware involved with image transfer in the

memory of the MFP Control Board (PWB-MFP) does

not respond.

C1290 Compression/extraction timeout

detection

• The hardware involved with the BTC compression

function offered by the MFP Control Board (PWBMFP)

does not respond.

C12B1 Image processing ASIC failure 1 • Image processing ASIC (CPS2300S) on the MFP

Control Board (PWB-MFP) does not respond.

C12B2 Image processing ASIC failure 2 • Image processing ASIC (PIC1200S) on the MFP Control

Board (PWB-MFP) does not respond.

C12B3 Image processing ASIC failure 3 • Image processing ASIC (PIC3400LITE) on the MFP

Control Board (PWB-MFP) does not respond.

C12B4 Image processing ASIC failure 4 • Image processing ASIC (BTCIF) on the MFP Control

Board (PWB-MFP) does not respond.

C12C0 Hard disk recognition error • Unable to communicate between the hard disk and

MFP Control Board (PWB-MFP).

C12C1 Hard Disk Error 1 • Hard disk is faulty.

C12C2 Hard Disk Error 2

C12C3 Hard Disk Error 3

C12C4 Hard Disk Error 4

C12C5 Hard Disk Error 5

C12C6 Hard Disk Error 6

C12C7 Hard Disk Error 7

C12C8 Hard Disk Error 8

C12C9 Hard Disk Error 9

C12CA Hard Disk Error A

C12CB Hard disk data transfer error • Data transfer from the hard disk is faulty.

C12CC Hard disk unformat • Unformatted hard disk is connected.

C12CF Hard disk specifications error • A hard disk that falls outside the specifications is connected.

C12D0 Controller hardware error • A controller hardware error is detected in the network

I/F.

C13C8 New Transfer Cleaner Unit resetting

failure

• A new installation is not detected when a new Transfer

Cleaner Unit (Image Transfer Belt Unit) is installed.

C13CA New Fusing Unit resetting failure • A new installation is not detected when a new Fusing

Unit is installed.

C13D1 Cyan Imaging Unit EEPROM

access error

• A condition of “EEPROM is not connected” or “There

is an access error” is detected in EEPROM of the

C13D2 Magenta Imaging Unit EEPROM Imaging Unit.

access error

C13D3 Yellow Imaging Unit EEPROM

access error

C13D4 Black Imaging Unit EEPROM

access error

C13D5 Cyan LPH correction data download

failure

• . An error is detected while the LPH correction data is

being downloaded from EEPROM of LPH to PWBC13D6

Magenta LPH correction data MFP when the Power Switch is turned ON.

download failure

C13D7 Yellow LPH correction data download

failure

C13D8 Black LPH correction data download

failure

C1800 Controller start failure • A controller start failure is detected in the controller

interface.

C3310 CCD clamp/gain adjustment failure • The adjustment value is 0 or 255 during a CCD clamp

adjustment.

• The peak value of the output data is 64 or less during

a CCD gain adjustment.

C3331 MSC undefined malfunction occurring

• An undefined malfunction occurs in the MSC of the

MFP Control Board (PWB-MFP).

C3332 Scanner Section undefined malfunction

• An undefined malfunction occurs in the Scanner Section.

C3333 Engine Section undefined malfunction

• An undefined malfunction occurs in the Engine Section

(PWB-MC, etc.).

C3E00 NVRAM initialization failure • Total Clear is executed in a mode other than the card

line mode.

C3E01 • An initial command is issued from the terminal in a

mode other than the card line mode.

C3E02 • A new NVRAM is detected in a mode other than the

card line mode.

C3F00 Vendor connection failure • It is detected that communications with the vendor are

interrupted for a given period of time or more with

"Installed" selected for the setting of vendor installation.

C3FFC ROM contents error upon startup

(LPH)

• A fault is detected in a sequence of ROM contents

check of the LPH Board during starting.

C3FFD ROM contents error upon startup

(Scanner)

• A fault is detected in a sequence of ROM contents

check of the PWB-C during starting.

C3FFE ROM contents error upon startup

(PRT)

• A fault is detected in a sequence of ROM contents

check of the Control Board during starting.

C3FFF ROM contents error upon startup

(MSC)

• A fault is detected in a sequence of ROM contents

check of the MSC (PWB-MFP) during starting

]]> http://copierservicereset.com/trouble-code-list-minolta-c350/feed service code list-warning- C350 http://copierservicereset.com/service-code-list-warning-c350 http://copierservicereset.com/service-code-list-warning-c350#comments Thu, 25 Feb 2010 21:13:26 +0000 admin http://copierservicereset.com/service-code-list-warning-c350

Code Item Description

S-1 CCD clamp gain adjustment failure

• It is detected that the CCD clamp gain adjustment

value is faulty.

P-5 AIDC Sensor (Front) failure • The output from the photoreceiver of the AIDC Sensor

that takes a reading of a point of a bare surface on the

Transfer Belt is 4.3 V or more during an adjustment of

the AIDC Sensor.

• The output from the photoreceiver of the AIDC Sensor

that takes a reading of a point in a toner pattern on the

Transfer Belt is 1.0 V or less after the adjustment has

been completed.

P-28 AIDC Sensor (Back) failure

P-6 Cyan Imaging Unit failure

• All density readings taken from the density pattern produced

on the Transfer Belt are 0.5 g/m

2 (AIDC Sensor

photoreceiver output) or less during max. density

adjustment (Vg/Vb adjustment).

P-7 Magenta Imaging Unit failure

P-8 Yellow Imaging Unit failure

P-9 Black Imaging Unit failure

P-21 Color Shift Test Pattern failure

• The number of points detected in the CD direction is

more or less than the specified value during CD registration

correction.

• The number of points detected in the FD direction is

more or less than the specified value during FD registration

correction.

P-22 Color Shift Test Pattern failure

• The color shift amount is greater than the specified

range during CD registration correction.

• The color shift amount is greater than the specified

range during FD registration correction.

• The skew correction amount is greater than the specified

value.

P-26 ATVC (Bk) failure

• An abnormal average value is detected during an

adjustment of the first image transfer ATVC value of

Black.

P-27 ATVC (2nd) failure

• An abnormal average value is detected during an

adjustment of the second image transfer ATVC value.

P-29 ATVC (color) failure

• An abnormal average value is detected during an

adjustment of the first image transfer ATVC value of

color.

P-30

Color PC Drum Main Sensor malfunction

• The output from the Color PC Drum Main and Sub Sensors

remains unchanged for a continuous period of

1,000 ms while the Color PC Drum Motor is turning stably

and the Lock signal is active (LOW-0).

P-31

Bk PC Drum Main Sensor malfunction

• The output from the Color PC Drum Main and Sub Sensors

remains unchanged for a continuous period of

1,000 ms while the Bk PC Motor is turning stably and

the Lock signal is active (LOW-

]]> http://copierservicereset.com/service-code-list-warning-c350/feed total counter and service password reset DI2510 http://copierservicereset.com/total-counter-and-service-password-reset-di2510 http://copierservicereset.com/total-counter-and-service-password-reset-di2510#comments Mon, 14 Dec 2009 21:07:19 +0000 admin http://copierservicereset.com/?p=354 This information is available only for the service stuff. 

In fact it’s ilegal to do that procedure in most europe countries.But in some cases it’s need to reset total counter or service password. You can find theese informations in ‘chip reseter’ page starting 20th of December 2009

]]> http://copierservicereset.com/total-counter-and-service-password-reset-di2510/feed bizhub c203/253/353, c451/c550/c650 DF611 jam http://copierservicereset.com/bizhub-c203253353-c451c550c650-df611-jam http://copierservicereset.com/bizhub-c203253353-c451c550c650-df611-jam#comments Fri, 03 Jul 2009 16:00:06 +0000 admin http://copierservicereset.com/?p=333 frequent jams on DF611 :

1. multiple feeding : swing up the adf paper feed tray. Under tray you will find a spring that press the separating roller (blue one). Set this spring on the lower position.

2. jams at the last sheet of paper :swing up-at left  only upper side of the adf paper feeed tray, swing up -at right elevator tray and remove it. Under elevator tray you will see a large white plastic part .this part lift up the elevator tray.On this part (white) you will see 2 small holes (like screw holes) insert in those holes 2 screws and screw it so remain only 2-4 mm out on white part

df611.jpg

The other reason for multiple jam on DF611 is bad setting of photo interrupter: to solve this -open-remove upper cover of paper df tray -inside you will find 3-4 photo interrupter .These is just inserted in their holes but it’s not fixed.When Df work and vibrate -these interrupter move freely in that holes. For best results you can use a quick adhesiv(bond) to fix it in right position

photo int..jpg

 

]]> http://copierservicereset.com/bizhub-c203253353-c451c550c650-df611-jam/feed c0500,c0501 minolta DI152,DI1611,bizhub162,bizhub163 http://copierservicereset.com/c0500c0501-minolta-di152di1611bizhub162bizhub163 http://copierservicereset.com/c0500c0501-minolta-di152di1611bizhub162bizhub163#comments Fri, 03 Jul 2009 14:43:26 +0000 admin http://copierservicereset.com/?p=328 how to reset this trouble ,reason for this code:

first- try to reset code c0500/c0501 : turn on the copier while you press stop key.

     - the trouble was reset? ok

    -the trouble show again? Check following parts: micro switch S2-you can adjust pressure and good work on that switch.

S2.jpg

     check also if the metal lever that push on microswitch work fine.In most cases this lever is set wrong or is realy broken (the hole  below it)

c0500.jpg

If everything seems to be Ok, remove the fusing unit and check thermosta(thermal fuse) or tube lamp

]]> http://copierservicereset.com/c0500c0501-minolta-di152di1611bizhub162bizhub163/feed how to extend drum life (color copiers) http://copierservicereset.com/how-to-extend-drum-life-color-copiers http://copierservicereset.com/how-to-extend-drum-life-color-copiers#comments Fri, 19 Jun 2009 19:34:57 +0000 admin http://copierservicereset.com/?p=320 In most cases the cylinder life ends before being effectively damaged and the copier will stop .

This procedure is established in software mode to maintain  a good quality copy &print.

To unlock the copier in this case you  must enter into "security mode" and switch "iu life stop setting" to "no stop" . How to enter in security mode…. if you are a true technician …you already know that… if you are end user….call a real techician

]]> http://copierservicereset.com/how-to-extend-drum-life-color-copiers/feed c0700 on minolta di350, di250 http://copierservicereset.com/c0700-on-minolta-di350-di250 http://copierservicereset.com/c0700-on-minolta-di350-di250#comments Wed, 03 Jun 2009 20:03:42 +0000 admin http://copierservicereset.com/?p=315

-toner motor is unable to rotate the toner bottle= The most likely cause is  wrong pointing of toner bottle 

Solving:

turn of the copier, pull out the toner bottle(don’t rotate the bottle

turn on the copier :

1. hear the noise behind the copier then- c0700 = the toner motor or toner rotate mechanism was broken -you must change the toner rotate mechanism or change all (motor +mechanism) with a new toner motor from EP 1050/1054-it works perfect.

2. c 0700  code appears immediately : first -check and repair the toner rotate mechanism-see above-

                                                                         :second- replace the blowed 1A fuse on PWB-A with new one

turn on the copier — everything seems ok ? insert toner bottle in correct position

]]> http://copierservicereset.com/c0700-on-minolta-di350-di250/feed bizhub series trouble reset procedure http://copierservicereset.com/bizhub-series-trouble-reset-procedure http://copierservicereset.com/bizhub-series-trouble-reset-procedure#comments Wed, 03 Jun 2009 19:41:23 +0000 admin http://copierservicereset.com/?p=313 To reset trouble code from konicaminolta bizhub series- 250,350,c250,c252,c203,c253,c353,c451,c550,c650…. follow this steps:

-turn of the copier

-pres and hold utility/counter key until turn on the copier.

-wait …. on the scrren will be see "trouble reset"

-touch "trouble reset"- OK will be see.

-turn off the copier

-wait 10 sec. then turn on the copier.

-if the trouble code will be shown again…..call a competent service technician.

]]> http://copierservicereset.com/bizhub-series-trouble-reset-procedure/feed