http://copierservicereset.com HOW TO RESET COPIER'S CHIPS IN THE CHEAPEST MODE Mon, 08 Mar 2010 17:20:33 +0000 http://backend.userland.com/rss092 en C0000 Main Motor ’s failure to turn The Main Motor Lock signal remains faulty for a predetermined’s’s’s failure’s’s failure to turn’s failure to turn’s failure to turn’s failure to turn C0060 Fusing Drive Motor to turn A Fusing Drive Motor Lock signal remains faulty for a predetermined continuous period of time while the Fusing Drive Motor ... http://copierservicereset.com/trouble-code-list-minolta-cf15012001 C0000 Main Motor Failure • The Transport Motor Lock signal remains set to H for a set period of time while the Transport Motor is turning. C0010 Imaging Unit Motor Failure • The Imaging Unit Motor Lock signal remains set to H for a set period of time while the Imaging Unit Motor is turning. • The Imaging Unit Motor ... http://copierservicereset.com/trouble-code-list-minolta-di2510   C0000Main Motor's failure to turn • The Motor Lock signal remains HIGH for a predeterminedcontinuous period of time while the Motor is turning. C0001 Main Motor turning at abnormaltiming • The Motor Lock signal remains LOW for a predetermined continuous period of time while the Motor remains stationary. C0016 Bk PC Motor's failure ... http://copierservicereset.com/trouble-code-list-minolta-c350 Code Item Description S-1 CCD clamp gain adjustment failure • It is detected that the CCD clamp gain adjustment value is faulty. P-5 AIDC Sensor (Front) failure • The output from the photoreceiver of the AIDC Sensor that takes a reading of a point of a bare surface on the Transfer Belt is 4.3 V or ... http://copierservicereset.com/service-code-list-warning-c350 This information is available only for the service stuff.  In fact it's ilegal to do that procedure in most europe countries.But in some cases it's need to reset total counter or service password. You can find theese informations in 'chip reseter' page starting 20th of December 2009 http://copierservicereset.com/total-counter-and-service-password-reset-di2510 frequent jams on DF611 : 1. multiple feeding : swing up the adf paper feed tray. Under tray you will find a spring that press the separating roller (blue one). Set this spring on the lower position. 2. jams at the last sheet of paper :swing up-at left  only upper side of the adf ... http://copierservicereset.com/bizhub-c203253353-c451c550c650-df611-jam how to reset this trouble ,reason for this code: first- try to reset code c0500/c0501 : turn on the copier while you press stop key.      - the trouble was reset? ok     -the trouble show again? Check following parts: micro switch S2-you can adjust pressure and good work on that switch.      check also ... http://copierservicereset.com/c0500c0501-minolta-di152di1611bizhub162bizhub163 In most cases the cylinder life ends before being effectively damaged and the copier will stop . This procedure is established in software mode to maintain  a good quality copy &print. To unlock the copier in this case you  must enter into "security mode" and switch "iu life stop setting" to "no stop" . ... http://copierservicereset.com/how-to-extend-drum-life-color-copiers -toner motor is unable to rotate the toner bottle= The most likely cause is  wrong pointing of toner bottle  Solving: turn of the copier, pull out the toner bottle(don't rotate the bottle turn on the copier : 1. hear the noise behind the copier then- c0700 = the toner motor or toner rotate mechanism was ... http://copierservicereset.com/c0700-on-minolta-di350-di250 To reset trouble code from konicaminolta bizhub series- 250,350,c250,c252,c203,c253,c353,c451,c550,c650.... follow this steps: -turn of the copier -pres and hold utility/counter key until turn on the copier. -wait .... on the scrren will be see "trouble reset" -touch "trouble reset"- OK will be see. -turn off the copier -wait 10 sec. then turn on the copier. -if the ... http://copierservicereset.com/bizhub-series-trouble-reset-procedure